Hanover, MD Air Conditioning, Heating and Plumbing Services

Supreme Service Today provides Air Conditioning, Heating and Plumbing Services, Repair, Installation, Maintenance, and Tune Up in Hanover, MD and surrounding areas.

Check out what some of our customers are saying about Supreme Service Today.

Local Reviews
for Hanover, MD

Supreme Service Today Rated 5.0 out of 5 stars based on 3 customer reviews

Map of Hanover, MD

Very easy




Review of Supreme Service Today


Map of Hanover, MD

Very easy




Review of Supreme Service Today


Map of Hanover, MD

Great Service!




Review of Supreme Service Today

We have been working with Supreme Air for several years now and have always had a great experience.


nikolayn@supremeservicetoday.com

nikolayn@supremeservicetoday.com

Up on arrival performed installation with Quentin of heat pump and air handler. Suggested Uv light , Ez trap , Service agreement 16.66$ monthly to customer. Customer approved labor and parts . After full install, checked system for operation, checked uv light and ez trap for operation. Everything working good at this time

Near Aragorn Ct, Hanover, MD 21076
marcm@supremeservicetoday.com

marcm@supremeservicetoday.com

Replace gate valve on main and add in a dual back flow.

Near Aragorn Ct, Hanover, MD 21076
marcm@supremeservicetoday.com

marcm@supremeservicetoday.com

Installed water heater for install and completed.

Near Aragorn Ct, Hanover, MD 21076
marcm@supremeservicetoday.com

marcm@supremeservicetoday.com

Took $539 for the deposit for the job. Will collect the remaining $539 when we complete the work on 1/24.

Near Aragorn Ct, Hanover, MD 21076
Joseph.Wade@supremeairllc.com

Joseph.Wade@supremeairllc.com

Replace board, TXV, and filter drier. Recover, recharge and test operations.

Near Arundel Mills Cir, Hanover, MD 21076
Joseph.Wade@supremeairllc.com

Joseph.Wade@supremeairllc.com

Performed heating pm on all units. Replaced filters. Inspected blowers, coils, and heat exchangers. Flushed out all drains. Checked capacitors and tightened electrical connections. Cleaned burners and flame sensors. Measured specs of igniters. Ran heat on all units. Checked amp draw of inducer and blower motors. Measured heat rise. All units are operating normal at this time.

Near Teague Rd, Hanover, MD 21076
Joseph.Wade@supremeairllc.com

Joseph.Wade@supremeairllc.com

On arrival removed rusted rollout switch ,i then installed new one .tested system operation.unit operating normal

Near Foxtrail Ct, Hanover, MD 21076
Joseph.Wade@supremeairllc.com

Joseph.Wade@supremeairllc.com

Repair lock nuts on trap under kitchen sink. Both were over tightened at one point and cracked. Replaced all of the lock nuts and pipe doped. Also did an inspection on the house. Found no issues around the house. Selling the house so wanted to make sure everything was good for an inspection.

Near Penzance Way, Hanover, MD 21076
Joseph.Wade@supremeairllc.com

Joseph.Wade@supremeairllc.com

Upon arrival found urinal to be working fine when I returned don’t know what happened but was not covered by a sign anymore. Addressed supervisor on duty they told me it just started randomly working again. So I advised them to keep an eye on urinal for a couple days just in case it’s the batteries or something to do with the unit itself.

Near New Ridge Rd, Hanover, MD 21076
Joseph.Wade@supremeairllc.com

Joseph.Wade@supremeairllc.com

Toilet is leaking only when water is turned on. When the company replaced the toilet the never tightened the bowl down and left the paper work inside the tank also. I will tighten bolts and replace the supply line while I’m there. Fixed toilet supply line which there is no more leaks on the toilet.

Near New Ridge Rd, Hanover, MD 21076
Joseph.Wade@supremeairllc.com

Joseph.Wade@supremeairllc.com

Replaced Faucet and works perfect now. No issues were found during installation.

Near New Ridge Rd, Hanover, MD 21076
Joseph.Wade@supremeairllc.com

Joseph.Wade@supremeairllc.com

Fall pm on 11/06/19 On arrival I sanded the flame rectification probe and checked burner arrangement the ignitor homes out to be in good condition checked all other electrical connections set unit to call for heat measured supply and return air temp measured voltage and amps inspected electrical connections checked drain and cleaned checked filter and replaced checked blower motor checked all other electrical connections checked temp rise DT 56 made for 30-70 degrees unit tested unit operating normal at this time. Recommended Uv lights installation and DUCT Cleaning also single surge protector needs to be installed to avoid future problems.

Near Colesbury Pl, Hanover, MD 20794
Joseph.Wade@supremeairllc.com

Joseph.Wade@supremeairllc.com

On arrival set units to call for heat measured supply and return air temp measured voltage and amps inspected electrical connections checked safeties . Found downstairs unit rollout switch rusted ,recommended replacing it .customer approved repair and paid in full .also checked heat exchangers.units are operating normal at this time.

Near Foxtrail Ct, Hanover, MD 21076
Joseph.Wade@supremeairllc.com

Joseph.Wade@supremeairllc.com

Arrived to complete fall season check up. Checked unit in heat test mode verified proper operation.found unit needs ez drip. Also found outdoor coils need cleaning. Signed customer up for service agreement. For year.

Near Forest Ln, Hanover, MD 21076
Joseph.Wade@supremeairllc.com

Joseph.Wade@supremeairllc.com

Up on arrival performed fall maintenance on 10/25/2019. Tested thermostat for operation, tested unit for operation. Took readings on compressor, capacitor. Took delta T, delta P Unit working good at this time.

Near Adcock Ln, Hanover, MD 21076
Marc M.

Marc M.

I have three estimates for work to be completed while on site. I looked over all the bathroom fixtures to make sure we leave nothing unturned for best service.

Near New Ridge Rd, Hanover, MD 21076
Joseph.Wade@supremeairllc.com

Joseph.Wade@supremeairllc.com

Up on arrival performed operational inspection. Changed all filters, checked all system. Condenser Unit # 4 and 5 highly recommend to install new capacitors

Near Teague Rd, Hanover, MD 21076
Colin T.

Colin T.

Performed leak search on both circuits for RTU #3. Found circuit 1 is leaking at the condenser (heating) TXV power head, quoting customer to replace TXV. Pressurized Circuit 2 to 500psi, while looking for Leak, pressure dropped to 460psi but I was unable to find leak. No evidence of oil either. Need to isolate Evap and Condenser coils to verify where leak is. Could not do so today because of thunderstorm.

Near Arundel Mills Cir, Hanover, MD 21076
Colin T.

Colin T.

Replaced condenser fan motor 2 and fan blade, replaced C1 and C2 capacitors for RTU #2. Also found remaining (2) 10mfd run capacitors are barely out of spec, quoting to replace. Then found K10 outdoor fan relay stuck closed and outdoor fan 1 is constantly running, quoting customer to replace relay. Returned power to system and ran ac. Tested both stages.

Near Arundel Mills Cir, Hanover, MD 21076
Colin T.

Colin T.

Replaced thermostat for RTU #3. Cut back all wires for clean connections. Returned power to unit and programmed thermostat for system, 2H/2C conventional. Tested ac and found both circuits empty, no 410a. 22lbs Circuit 1, 23lbs Circuit 2, 45lbs of 410a total, leak search needed to identify if repairs can be made.

Near Arundel Mills Cir, Hanover, MD 21076
Joseph.Wade@supremeairllc.com

Joseph.Wade@supremeairllc.com

Unit #1 all components working properly and system cooling properly, no concerns. Unit #2 same, cooling properly no concerns. Unit #3 superheat really high when checked but unit still cooling properly, system slightly low on charge, doesn’t seem to be effecting unit but recommend leak search to be sure. Unit #4 pressures seems normal but not cooling very well, system needs to be monitored. Unit #5 cooling properly, no concerns at this time.

Near Teague Rd, Hanover, MD 21076
Joseph.Wade@supremeairllc.com

Joseph.Wade@supremeairllc.com

Checked out shower tile is leaking total length inside shower is 58” then a 12” seat pan is a 48” x 32” width of shower is 29” finish to finish in seat area

Near Hardwick Ct, Hanover, MD 21076
Joseph.Wade@supremeairllc.com

Joseph.Wade@supremeairllc.com

When I arrived I removed old creak condensation line install re-piped a new three-quarter inch condensation line. Remove water that was sitting in the drip pan wipe down clean unit .

Near Elmcrest Rd, Hanover, MD 21076
Youssef  D.

Youssef D.

On arrival found bad thermostat,replaced it ,tested system .checked pressures.unit operating normal.customer has no email .plz text or call

Near Colesbury Pl, Hanover, MD 20794
Youssef  D.

Youssef D.

When I arrived customer explain to me everything that happened with previous company that work on unit before. when I check out unit drip pan it was full of water. And I notice a crack on condensation pipe. So I vacuum up the water 4 gallons. System is running find, for now problem needs fix soon. Or safety switch with shut off system.

Near Elmcrest Rd, Hanover, MD 21076
MarkM@supremeairllc.com

MarkM@supremeairllc.com

Checked 4 RTU’s. Found multiple problems. We will sent you a quote and a better description of what needs to be done to repair the 4 units.

Near Arundel Mills Cir, Hanover, MD 21076
MarkM@supremeairllc.com

MarkM@supremeairllc.com

Was unable to complete the maintenance. Need a second man for the roof access to get to the condensers.

Near Teague Rd, Hanover, MD 21076
Colin T.

Colin T.

Upon arrival I spoke to Kyle at BWW, he wasn’t sure how to get onto roof so I walked to mall management office. Office isn’t open on the weekend but security guard informed me that we will need to call mall management 4105405100 and give them our information so they can give us clearance to the roof. Then they will schedule an appt with us where they will have an escort show us the roof access. Could not perform service today.

Near Arundel Mills Cir, Hanover, MD 21076
roberts@supremeairllc.com

roberts@supremeairllc.com

Found condenser fan running but the compressor was not. Checked compressor windings. Found windings to be closed and not grounded. Checked the capacitor and found it to be bad. Installed a new capacitor. Made all wiring connections. Checked operation.

Near Gaspar Drive, Hanover, MD 21076
Youssef  D.

Youssef D.

On arrival set units to call for cooling measured supply and return air temp measured voltage and amps inspected electrical connections checked drain and cleaned them .checked coils ,blowers,caps,contactors,units are operating normal .custmer signed up for membership

Near Foxtrail Ct, Hanover, MD 21076
Yonas M.

Yonas M.

Spring Pm On 04/19/19 On arrival set unit to call for cooling measured supply and return air temp measured voltage and amps inspected electrical connections checked drain and cleaned checked filter cleaned checked EWP and LWP water pressure and temp perfect checked compressor capacitor good unit tested unit operating normal at this time highly recommended Evaporator coils and duct work needs to be cleaned.

Near Adcock Ln, Hanover, MD 21076
ALEX K.

ALEX K.

Have someone come out to test ductwork for leaks for final inspection.

Near Forest Ave, Hanover, MD 21076
Christopher A.

Christopher A.

Customer needs to have the ductwork tested with a pressure hood to ensure there is minimal air leakage. This test is required for a final in Anne Arundel County. I arrived thinking there was an issue with static pressure or any other normal operational concerns I could check out. The test required is very specific and Supreme Air can schedule someone to come out to perform this test. I made an estimate to do this and explained to the customer. I asked the customer for payment for the duct testing and for the trip fee for today. Customer asked that the office please call them to handle payment. I called the office manager and the service manager to let them know the circumstances and the office will reach out to the customer to follow up with scheduling the duct pressure test.

Near Forest Ave, Hanover, MD 21076
michaelr@supremeairllc.com

michaelr@supremeairllc.com

On arrival checked thermostat was calling for AC: measure temp coming in and temp going out, voltage, AMPS, electrical connections,replace filter provided by customer (16x20x1),contactor, voltage absorption system rated for 40mf,actual 41.6. System is operating normal at this time.

Near Nauitan Ct, Hanover, MD 21076
Yonas M.

Yonas M.

Fall pm on 02/13/19 On arrival set units to call for heat measured supply and return air temp measured voltage and amps inspected electrical connections checked drain and cleaned checked filters and replaced checked heat exchangers checked coils is cleaned .no recommendation unit operating normal at this time.

Near Teague Rd, Hanover, MD 21076
michaelr@supremeairllc.com

michaelr@supremeairllc.com

On arrival set unit to call for heat,unit responded ok ,checked defrost ok,checked electric heat .114 leaving .unit operating normal

Near Maple Ave, Hanover, MD 21076
Daniel M.

Daniel M.

Found burnt contactor at outdoor unit . Replaced contactor and checked operations. Suction presssure 115 and head pressure 310. System is operating

Near Maple Ave, Hanover, MD 21076
Colin T.

Colin T.

Upon arrival I was told that neither HeatPump or aux heat were working. During diagnostics I found 30amp fuse blown on Common side of circuit. Replaced and tested, fuse blew right away. Shut off power to breakers and found all Compressor leads were grounded. Checked compressor terminals and found the same. Compressor needs to be replaced, R22 system. Then I went indoors and checked aux heat operation. Found heater pulling 40amps, in spec, but aux heater dropped out on high Limit shortly after. Opened up all panels and found evap coil almost completely restricted, dirty blower wheel, and a lot of spider webs in duct. Can also see droppings of dry wall and trash in bottom of return. Evap coil and blower need to be cleaned. Customer should have ducts cleaned as well. In all, Compressor needs to be replaced, evap coil and blower wheel needs to be cleaned, and ducts need to be cleaned. Suggesting system get replaced by severity of repairs. R22 system that needs a compressor will have to use

Near Fairbanks Ct, Hanover, MD 21076
Daniel M.

Daniel M.

Replaced condenser fan motor and checked operations . Supply air 88 degrees and return air 68 degrees . System is operating properly

Near Maple Ave, Hanover, MD 21076
Christopher A.

Christopher A.

Variable speed outdoor fan motor had line voltage and a nominal amp draw but does not operate. I filled out a part order form. Part and repair covered under Trane 10 year extended warranty, verified by the office.

Near Maple Ave, Hanover, MD 21076
Christopher A.

Christopher A.

Customer filled me in on the recent service regarding a refrigerant leak and asked that I look for any sign that the problem remains unresolved. I’m happy today that the unit has normal temperature rise in second stage heating of +25 degrees. The flow rate is set higher than how we set up the flow rates at 3gpm per ton of capacity but the heat of extraction is normal for a flow rate of more than 4gpm per ton of capacity. The flow rate cannot be adjusted either as there is no valve on the piping. I pressurized the loop to 65psi. I checked the electrical wiring and electrical systems, all are within specification. Customer cleans the filter frequently and the coil and blower are clean. Blower speeds were set correctly for this unit. I did decrease the differential for auxiliary heat from 3 to 2 degrees. The unit should rarely go into auxiliary heat but with winter coming I explained to the customer why it sometimes needs to and if the differential is to high it can cause problems. No f

Near Adcock Ln, Hanover, MD 21076
Yonas M.

Yonas M.

Trane indoor unit service Maintenance arundel mills Md

Near Nauitan Ct, Hanover, MD 21076
Hanover, MD - Trane indoor unit service Maintenance arundel mills Md
Daniel M.

Daniel M.

Checking operations on a Carrier Air handler in Hanover,MD.

Near Fairbourne Ct, Hanover, MD 21076
Hanover, MD - Checking operations on a Carrier Air handler in Hanover,MD.